7 Best 10 Inch Table Saw Blades to Buy In 2022

The default blade that comes with a table saw is usually a low-quality generic blade. Therefore, it’s the first item you should try to change and enhance after purchasing the saw. There is a vast range of sizes and shapes available for table saw blades, each designed for a specific task.

Considering that 10-inch-diameter blades are the norm for table saws, that’s what I’ve focused on here. Investing in the best 10 inch table saw blade in the market is a small price for increased productivity and quality.

Product
Top Pick
DEWALT 10-Inch Miter / Table Saw Blades,...
Runner Up
Freud LM72R010: 10" Heavy-Duty Rip Blade
Premium Pick
Forrest WW10307100 Woodworker II 10-Inch...
Prime
-
Pros
Effortlessly and tidily operates
Full kerf
Fresh and silent cut
Top Pick
Product
DEWALT 10-Inch Miter / Table Saw Blades,...
Prime
Pros
Effortlessly and tidily operates
My review
Runner Up
Product
Freud LM72R010: 10" Heavy-Duty Rip Blade
Prime
Pros
Full kerf
My review
Premium Pick
Product
Forrest WW10307100 Woodworker II 10-Inch...
Prime
-
Pros
Fresh and silent cut
My review

Top 7 Best 10 Inch Table Saw Blades Reviewed

  1. DEWALT DW3106P5 10-Inch Table Saw Blades – Top Pick
  2. Freud LM72R010 FTG Ripping Saw Blade – Runner Up
  3. Forrest WW10307100 Woodworker II – Premium Pick
  4. Freud D1080X Diablo ATB Saw Blade
  5. WEN BL1060C Apex Woodworking Saw Blade
  6. Makita B-66977 Carbide-Tipped Miter Saw Blade
  7. CMT 201.024.10 Industrial Ripping Saw Blade

The table saw blades on this shortlist are among the best available and can be used for a variety of tasks, like ripping a stack of boards at once and cutting precise grooves for cabinetry. Take a look at 10-inch table saw blade reviews.

1. DEWALT DW3106P5 10-Inch Table Saw Blades – Top Pick

Specification

  • Brand:‎ ‎ ‎Dewalt
  • Product Dimensions: 14.7 x 11.4 x 0.6 inches
  • Number Of Pieces: ‎60
  • Weight: 3 pounds

This thin-kerf blade has 60 ATB teeth and can make crosscuts at a fraction of the cost of similar offerings from rivals. Crosscut blades have a lot of teeth, which don’t cut quite as deeply.

Although this produces smoother crosscuts, the slower feed rate makes it impractical for lengthy rip cuts. Carbide teeth are less pronounced than on more pricey blades.

There is no better value for equipping a table saw than this two-pack, and both blades are top-notch. I like them even though they won’t hold a sharp edge for long. As time goes on, you’ll need to replace them. Anyways, try them, and you will not be disappointed.

PROS:
  • Effortlessly and tidily operates;
  • No significant cracking, even on melamine;
  • Smooth minimally-burning cuts;
  • Produces decent ripping results at slower feed;
  • Buying in pairs is a great deal.
  • It’s precise and reliable.
CONS:
  • Reduced tooth protection due to less carbide;
  • Not easy to sharpen more than a few times before it has to be replaced.

2. Freud LM72R010 FTG Ripping Saw Blade – Runner Up

Specification

  • Brand:‎ ‎Freud
  • Product Dimensions: ‎10.1 x 10 x 0.65 inches
  • Number Of Pieces: 30
  • Weight: 1.9 pounds

The 24 teeth of this blade are made of high-density carbide, which Freud calls their “ripping blend.” This material makes the blade more durable and suitable for cutting both softwoods and hardwoods. Teeth are made from a special titanium carbide and cobalt alloy developed by Freud specifically for that purpose.

When adjusted properly, a circular saw may cut through hardwoods with almost no vibration, producing e straight and smooth cuts for gluing. While testing this product, I appreciated that the blade produces very little noise.

The blade may be used with minimal noise because of 8 vibration-dampening slots laser-cut into the body and four more expansion holes around the edge.

PROS:
  • Outstanding carbide and tooth configuration;
  • Full kerf;
  • Delivers glue-line joints, even on a benchtop table saw;
  • Many cuts are ready to glue right off the saw;
  • Allow cutting dadoes and other grooves with perfectly flat bottoms;
  • Cuts smoothly even in lower-powered table saws;
  • Very quiet operation.
CONS:
  • Purpose-built for ripping only;
  • Possibility of chipped teeth upon arrival or shortly after use.

3. Forrest WW10307100 Woodworker II – Premium Pick

Specification

  • Brand:‎ ‎Shop ‎Forrest
  • Product Dimensions: ‎10.8 x 10.6 x 1.1 inches
  • Number Of Pieces: 30
  • Weight: ‎2.04 pounds

This table saw blade might appear expensive, but its exceptional performance and adaptability make up for the expense. While testing it, I was satisfied with clean rip cuts and crosscuts thanks to its alternative top bevel tooth design. It has low noise and vibration levels.

Excellent edge finish is achieved on rip and cross cuts in soft and hardwoods up to 2 inches in thickness thanks to the blade’s 15-degree ATB tooth design and 20-degree hook angle. Glue-line joints are feasible with a great consistent flow rate.

Forrest guarantees its blades for 30 days and has a good reputation for producing high-quality products. During that period, if you change your mind about the item you bought, you can send it back and get a complete refund.

Forrest also provides excellent value in the form of after-sale services, such as blade sharpening and service at low prices. This alternative is far more cost-effective than purchasing a new blade.

PROS:
  • Fresh and silent cut;
  • Cheap, high-quality knife blades;
  • Both rip and cross cuts feed well;
  • Reduces or gets rid of splintering at the crosscut’s bottom while making radial cuts.
CONS:
  • The blade is expensive.

4. Freud D1080X Diablo ATB Saw Blade

Specification

  • Brand:‎ ‎‎Freud
  • Product Dimensions: ‎6.25 x 0.82 x 0.51 inches
  • Number Of Pieces: 80
  • Weight: ‎2.4 ounces

The 80-tooth blade with a 2-degree tooth angle is ideal for plywood and MDF cutting. It cuts tough timber with a mirror finish and no splinters. It produced neither tangible vibration nor loud noise.

In comparison with a specialized finish blade, the broad gullets between each group facilitate the removal of more material during rip cuts. The blade may expand from the cut heat thanks to the laser-carved heat expansion holes.

In combination with its shock-resistant carbide structure, this blade is up to handle most of your table saw’s cutting needs.

PROS:
  • Excellent teeth arrangement;
  • Makes a kerf that’s neat and accurate;
  • Needing almost minimal or no sanding;
  • Cuts effortlessly through the densest of forests;
  • Treatment for damaged teeth and teeth sharpening at the factory for a reasonable price;
  • Reduced vibration when sawing through solid timber;
  • Compared to similar blades, this one makes far less noise.
CONS:
  • More likely to cause fires in the wood than others;
  • The unusual production technique makes it difficult to get them sharpened in a nearby shop.

5. WEN BL1060C Apex Woodworking Saw Blade

Specification

  • Brand:‎ ‎ WEN
  • Product Dimensions: ‎13.58 x 13.5 x 0.55 inches
  • Number Of Pieces: 60
  • Weight: 1.65 pounds

WEN’s blade can withstand RPMs of up to 6,000, allowing for rapid ripping and crosscutting. The WEN BL1060C is compatible with both table and miter saws, and its carbide-tipped teeth make quick work of any solid wood.

The heat expansion grooves in the table saw blade allow it to expand or contract depending on the ambient temperature, allowing for more or less cutting action depending on the situation.

The BL1060C has a protective coating that will keep the blade safe from high temperatures, corrosion, and rust. My coworker recommended it to me as his favorite table saw blade. These are narrow kerf blades, and they will make the saw more productive.

PROS:
  • Can handle RPMs up to 6,000;
  • Carbide-tipped teeth;
  • Thin kerf blades;
  • Protective coating;
  • Lightweight and thin;
  • Easy to adjust with the tool.
CONS:
  • Not recommended for non-ferrous or ferrous metals;
  • Not as fine as an 80-tooth count blade.

6. Makita B-66977 Carbide-Tipped Miter Saw Blade

Specification

  • Brand:‎ ‎ ‎Makita
  • Product Dimensions: ‎0.25 x 11.5 x 13.5 inches
  • Number Of Pieces: 80
  • Weight: ‎1.65 pounds

Makita is a popular brand of power tools and related items. You can expect good results from your miter saw crosscuts thanks to the 10-inch blade’s 80 teeth. Micropolishing using 600 grit materials has been done on each tooth. So you may then use it to make clean cuts with the blade.

Makita was a nice blade to test since it cuts well and costs less than the ones I normally get from large box retailers. It does not require sharpening and may be used for a very long time without any loss of cutting efficiency.

PROS:
  • Very clean cut;
  • Reasonable price;
  • A carbide material in the build helps to extend the life of the blade;
  • The cuts that it makes seem precise.
CONS:
  • It may generate more noise than other blades.

7. CMT 201.024.10 Industrial Ripping Saw Blade

Specification

  • Brand:‎ ‎CMT
  • Product Dimensions: 10 x 10 x 0.13 inches
  • Number Of Pieces: 24
  • Weight: 2 pounds

This blade works wonderfully for any purpose and has served me well over a long time of table sawing. It can maintain its edge for a very long time if kept clean.

You may use it for ripping cuts, but it’s not the greatest for smoothing off rough edges. Ripping hardwoods is a breeze with the CMT. The table saw blade’s narrow kerf design aids in this regard by minimizing the quantity of material taken from the wood during cutting. It’s a good choice because of its sharpness and durability.

PROS:
  • Produces exceptionally clean, smooth cuts;
  • Excellently engineered to dampen vibrations;
  • Competitive cost;
  • Excellent worth.
CONS:
  • Not great for completing work.

Buyer’s Guide on 10-Inch Table Saw Blade

It’s not easy to narrow down your options. I have listed the most important criteria to consider when selecting a table saw blade.

Blade size and dimensions

The blade length I would suggest is the 10-inch table saw blades. A bigger blade, say 12 inches long, will be much more unstable. A larger table saw blade has a larger cut capacity and can thus cut through thicker material in less time, albeit at the expense of accuracy. If the blade is narrower, it may spin at a higher RPM, resulting in cleaner cuts and better finishes.

Compatibility

Table saws typically accommodate a 10-inch blade. However, some may be adjusted to use shorter blades. Try not to force a bigger blade into a 10-inch table saw.

black saw blade tines

Teeth gullet

The gullet is the distance in millimeters between the blades’ teeth. With any blade, the gullet size decreases as more teeth are added to a given blade. For instance, a blade with 80 teeth will have a substantially narrower gullet than a 50-tooth alternative. The gullet is a major indicator of the blade’s ability to remove the material with each cut and indicates accuracy.

Kerf

Higher kerfs allow the blade to cut through more material without tearing. Full kerf blades, or 1/8-inch kerf, are the most common types which can cut with less deflection than thinner blades. The broader the saw blade’s kerf, the less vibration it will cause. For the same cutting efficiency, a thinner kerf blade will require less power than a larger one.

Material and manufacturing

The blade’s quality of construction is crucial to the tool’s lifetime and use. A saw that loses its sharpness after only a few cuts is unacceptable. It might be inconvenient even if the maker offers free sharpening services. In my opinion, the best blade materials to use are steel with tungsten carbide tips.

10 inches Red saw blade

Type of table saw blade

To choose the best saw blade for the work, it is important to understand how different blades cater to different demands. See the list of saw blades for some of the most popular ones on the market.

Crosscut

Manufacturers create crosscut saw blades to achieve clean cuts across the wood grain. Extra teeth have been added to these saws. Compared to a ripping or combination blade, the 60 to 80 teeth on a crosscutting blade of 10 inches will allow it to make more cuts each rotation.

Crosscut blades remove less material between each tooth and require more time to cut through wood. When accuracy and a clean cut are paramount, finish carpentry is one of the many uses for crosscut blades.

Flat-tooth ripping and rip-only

These blades have flat tooth designs to efficiently remove more wood fiber. A ripping blade’s teeth are sharper and set at an angle of at least 20 degrees, with the average number of teeth being 10.

With fewer teeth on the blade, the gullets may be made bigger, which speeds up the stock removal process. They are not functional for crosscutting because of the excessive tear-out they cause and are best suited for the rough carpentry construction site, where speed and power are valued above precision.

large silver disc

Combination and alternate top bevel (ATB)

They are versatile tools used to make cross cuts and rips. The 40-80 tooth count is a happy medium between those crosscut and ripping saws. Maybe they’re not the ideal blade for ripping or crosscutting, but they can still get the job done. When you look at the teeth of a combination blade, you’ll see that there are little gullets between each set, followed by a larger gullet and another set of teeth.

FAQ About Table Saw Blades

There are so many options when it comes to blades that you’re bound to find one that works for your next DIY endeavor. If you have any questions about table saw blades, you may look them up here.

What is the best 10-inch table saw blade?

The ideal blade for a table saw might change from job to job. The DEWALT DW3106P5 is a good all-around saw blade that would serve you well in most situations. It may be used for a wide variety of cuts, producing a high-quality result every time.

Can you put a 7-inch blade on a 10 inch table saw?

It is possible to utilize a 7-inch blade with a table saw that typically takes a 10-inch blade. However, you may use a smaller blade at the expense of some cutting depth. The smaller blade will produce less noise and less sawdust.

How thick is a 10 inch table saw blade?

The highest depth of cut for a 10-inch table saw is 3.5″, but a 12-inch saw can go to a depth of 4 inches. A typical blade has a kerf width of .07 inches, while a narrow blade measures only .042 inches.

What size dado blade for a 10-inch table saw?

Dado blades with an 8-inch diameter are designed with a 10-inch saw since they are not intended for thorough cuts. Dado sets with a 10-inch width are quite uncommon. A 10-inch dado set is much for most saws to handle.

Make a Right Choice

I’ve evaluated some of the finest tables saw blades on the market to help you choose the ideal one. Think about your task and pick the blade that will serve you best. The DEWALT DW3106P5 has 2 blades, makes clean cuts, lasts a long time, and produces good results. Therefore, it’s my top choice.

Best 10-inch table saw blade — comparison table

ProductTooth CountTooth ConfigKerf
DEWALT DW3106P5 10-Inch Table Saw Blades60ATB 0.095”
Freud LM72R010 FTG Ripping Saw Blade 24 flat1/8”
Forrest WW10307100 Woodworker II 40ATB1/8”
Freud D1080X Diablo ATB Saw Blade80ATB0.098”
WEN BL1060C Apex Woodworking Saw Blade 60ATB1/10”
Makita B-66977 Carbide-Tipped Miter Saw Blade80ATAFR0.085"
CMT 201.024.10 Industrial Ripping Saw Blade24Rip Blade0.098”

If you were about to make a purchase of a table saw blade, which one would you choose? Drop us a comment below if you’re still searching for your favorite or have already found it.

Sean Chapman

Sean Chapman

My ultimate goal is to provide insights that will help you effectively determine whether this or that tool or product suits your needs/budget or not. I test out home improvement tools at work on a daily basis and enjoy sharing my knowledge with D.I.Y-ers who have similar questions to the ones I used to have. I realize how important choosing the right tools is, that’s why my approach to every review I publish is very responsible.

We will be happy to hear your thoughts

Leave a reply

Solve : *
25 − 24 =


Tools n Goods
Logo